29 July 2011

NL6274: Lining & Facing with Petersham

Attaching the Lining to the Zipper Tape:
This is actually quite simple. I used this tip found on Pattern Review. The tip works if you want to attach a facing, lining, or facing-lining combo to the zipper tape without any hand-sewing.

In the tip, Belinda says to let the facing/lining overhang the seam by 5/8" (1.5 cm). She included a picture of the overhang, but for some reason I can't wrap my mind around the photo or how the overhang factors in to sewing the facing/lining to the zipper tape.

1. Insert the zipper as usual and assemble the lining (facing or facing-lining combo). Arrange the shell and lining so that the right sides face in.



2. Pin the lining to the zipper tape right sides together. I sewed using a 3/8" seam allowance since I didn't quite understand the purpose of the overhang in the tip. This doesn't seem to be posing a problem.



3. Here the right sides are stitched.



4. Turn the lining to the inside so that wrong sides face. Baste



Facing the Waist with Petersham:
Most of the work is done in shaping the petersham to achieve a nice curve so that it molds comfortably around the waist. I used 1.5" wide petersham cut to a length equal to the circumference of my waist where I'll wear the skirt, plus about 2 inches for overlap.

1. Soak the petersham in hot water for a few seconds. Lightly pat dry.

2. Shaping the petersham requires a hot iron a bit of force. I anchored one end of the ribbon to my ironing board using glass-head pins.



3. Moving from one short end to the other, press and stretch one long edge while gently building in a curve on one edge. I don't know if there is a rule or something about how much curve should exist. I just winged it. I've done this twice and don't notice any difference. =)



4. Pin the non-stretched edge to the waist seamline. Since the shell and lining are basted, the seamline is easily visible. The stretched edge should hang off the top of the skirt. In this case, I found pinning parallel to the seamline gave me more stability and control. I was very careful to remove the pins before they reached the presser foot!



5. Edgestitch in place.




6. Turn the petersham to the inside and press, taking care to roll the seam in a bit.






finished inside

While these steps admitted take longer in sewing the skirt, the effort is well worth it. I think this skirt will wear well and last a while. I've worn the flounced skirt so many times already; I just love it.

I'm off to work more on my summer 6PAC. Update coming soon...

Be well!

L

22 July 2011

NL6274: Invisible Zipper

I think I finally got the hang of installing invisible zippers (IZs) successfully. IZs installed in side seams can be tricky since the seams are usually curved. I found that taking extra care in the beginning and stitching slowly help to make installation quite simple.

Tools:
  • invisible zipper foot
  • contrasting thread
  • regular zipper foot
I use an invisible zipper foot by Unique. I found it at a thrift store for $0.50 and love it. I used to use the YKK zipper foot, but I like the Unique one much better. It has a single hole opening (sort of like a straight stitch foot) and deeper grooves for the zipper coil.



1. Using a medium warm iron, press the zipper coils flat. This helps the coils feed through the specially designed groove on the IZ foot.

2. On the skirt front and skirt back, sew a guide line along the seam using contrasting thread. It's kind of hard to see in the photo. The contrasting thread is orange on the right-hand side.



3. On the skirt front and back, fold the seam along the guideline to the inside. Press.



4. Place the zipper (face down) on top of the skirt back (right side up). As oriented, pin the left side of the zipper to the seam allowance making sure that the zipper coils are on the guideline/crease. I like pinning vertically because I can stabilize the zipper more efficiently.



5. Stitch. If you pinned vertically, be careful not to strike the pins! When sewing, I usually place my finger on the pin tip and sew until the presser foot meets my finger. I haven't had have any mishaps doing it this way.


6. To make sure everything lines up (reasonably) well, use chalk to mark match points across the entire zipper and skirt front by lining up the waist seam, hem, and seamlines accordingly. Usually I am pretty good with the match points, though, I admit that I am off a tiny bit on this one. Oh well. I am *not* unpicking this zipper. Really, who will know?



7. Now it's time to attach the right side of the zipper to the skirt front. This takes a little maneuvering, but not Houdini-like. Place both the skirt front and skirt back side by side, right side up. The left side of the face-down zipper should be sewn to the skirt back. With the free zipper tape right side down, orient (by turning) so that the zipper tape is face down on the skirt front with the coils aligned with the guideline/crease. It should only take one turn (hmm...maybe a turn and a half) of the tape to make this happen.



Use the markings on the zipper tape to match the skirt front. Pin and stitch.



8. Close the zipper. Using a standard zipper foot, secure the tape ends to the seam allowances.



9. Finally, finish the seam allowance beneath the zipper. At present, I haven't found the best way to make this part easier. I've been searching for a very narrow zipper foot for my machine. Cleaner's Supply sells zipper feet, but I'm not sure it will fit. I'll buy it (provided there is a return policy) and see. Until then, I use my standard foot (zigzag) and get as close as I can to the area beneath the zipper.


Up next: Attaching the lining to the zipper tape.

Be well!

L

LinkWithin

Related Posts Plugin for WordPress, Blogger...